{"id":3829,"date":"2026-10-23T00:20:03","date_gmt":"2026-10-22T16:20:03","guid":{"rendered":"https:\/\/sayoon-dc.com\/blog\/dc-contactors-in-parallel-current-sharing\/"},"modified":"2026-11-09T00:18:58","modified_gmt":"2026-11-08T16:18:58","slug":"dc-contactors-in-parallel-current-sharing","status":"publish","type":"post","link":"https:\/\/sayoon-dc.com\/ru\/blog\/dc-contactors-in-parallel-current-sharing\/","title":{"rendered":"\u041a\u043e\u043d\u0442\u0430\u043a\u0442\u043e\u0440\u044b DC \u0432 \u043f\u0430\u0440\u0430\u043b\u043b\u0435\u043b\u044c\u043d\u043e\u043c \u0440\u0435\u0436\u0438\u043c\u0435: \u0441\u043e\u0432\u043c\u0435\u0441\u0442\u043d\u043e\u0435 \u0438\u0441\u043f\u043e\u043b\u044c\u0437\u043e\u0432\u0430\u043d\u0438\u0435 \u0442\u043e\u043a\u0430 \u0438 \u0444\u0443\u043d\u043a\u0446\u0438\u044f \u043f\u0435\u0440\u0435\u043a\u043b\u044e\u0447\u0435\u043d\u0438\u044f \u043d\u0430\u0433\u0440\u0443\u0437\u043a\u0438"},"content":{"rendered":"<p>DC contactors in parallel do not automatically share current equally or acquire the sum of their individual switching ratings. Unequal branch resistance affects steady current, while contact timing determines which device first makes and last breaks the load. Use a parallel arrangement only where the exact product combination and installation have documented support. A larger single contactor with suitable ratings is often easier to verify than two smaller devices joined by an improvised busbar.<\/p>\n<p>This guide addresses multiple contactors connecting the same two electrical nodes. Separate contactors serving separate battery strings are a different architecture: those strings have their own sources and protection requirements, rather than being interchangeable parallel switch branches.<\/p>\n<h2>Start with the complete branch resistance<\/h2>\n<p>A parallel branch contains more than the main contacts. Cable length, conductor section, terminal joints, busbar geometry and measurement shunts all contribute resistance. The voltage across the branches is common, but their currents depend on their complete impedances. Equal part numbers alone cannot establish equal installed resistance.<\/p>\n<p>OpenStax&#8217;s series-and-parallel resistor explanation provides the basic circuit relationships. For a steady resistive approximation, branch current is voltage divided by branch resistance. This is a useful screening calculation, not a model of contact bounce, arcing or dynamic interruption. Contact resistance and joint condition also change with temperature, wear and installation history.<\/p>\n<p>A symmetric drawing is therefore only a starting point. Actual terminal stack-up, assembly torque and cooling can create an asymmetric installation. Evaluate the finished current paths rather than comparing the nominal contactor ratings in isolation.<\/p>\n<h2>A numerical example of unequal sharing<\/h2>\n<p>Assume, solely for illustration, that two complete branches measure 0.4 milliohm and 0.6 milliohm at a defined condition. Their conductances divide a 200 A total into approximately 120 A and 80 A. The lower-resistance branch carries 60 percent of the current, not 50 percent. These are hypothetical values, not Sayoon product specifications.<\/p>\n<p>The equivalent resistance is 0.24 milliohm, giving about 0.048 V across the parallel combination. Branch power is approximately 5.76 W in the first path and 3.84 W in the second. Those values describe the complete assumed paths; they should not be attributed solely to the contact tips.<\/p>\n<p>Real temperature rise depends on where those losses occur and how heat leaves the assembly. A small terminal hot spot and a broadly distributed conductor loss can have the same total watts but very different consequences. Use measured branch current and appropriate thermal evidence together.<\/p>\n<figure><img decoding=\"async\" loading=\"lazy\" src=\"https:\/\/sayoon-dc.com\/wp-content\/uploads\/2026\/05\/czw400a_s1-2.webp\" alt=\"SAYOON DC contactor product view\"><\/figure>\n<h2>Closing and opening create different problems<\/h2>\n<p>The first contactor to close may make the entire load before the second branch becomes conductive. With a capacitive load, that first event may include the inrush peak. Adding a second parallel branch afterward does not undo the duty already imposed on the first device.<\/p>\n<p>During opening, one device may stop carrying before the other. The remaining closed branch then receives the current that the system continues to demand. The last contactor to separate may face the complete interruption duty. Assuming that each device breaks half the current can therefore be substantially wrong.<\/p>\n<p>Commands sent in the same controller scan do not guarantee simultaneous contact movement. Coil supply, suppression, mechanical variation and temperature influence the actual timing. Even a test showing nearly equal timing on one occasion does not remove the need to assess the supported operating envelope.<\/p>\n<h2>Review the arrangement by operating state<\/h2>\n<div class=\"sy-table-wrap\">\n<table>\n<thead>\n<tr>\n<th>Condition<\/th>\n<th>Evidence to collect<\/th>\n<th>Decision<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Steady carry<\/td>\n<td>Simultaneous branch currents and temperature<\/td>\n<td>Assess actual imbalance<\/td>\n<\/tr>\n<tr>\n<td>Closing<\/td>\n<td>First device to conduct and load inrush<\/td>\n<td>Verify complete making duty<\/td>\n<\/tr>\n<tr>\n<td>Opening<\/td>\n<td>Last device carrying current<\/td>\n<td>Verify complete interruption duty<\/td>\n<\/tr>\n<tr>\n<td>One branch open<\/td>\n<td>Remaining branch load and response time<\/td>\n<td>Prevent unsupported continuous overload<\/td>\n<\/tr>\n<tr>\n<td>One branch welded<\/td>\n<td>Actual current path after off command<\/td>\n<td>Confirm required isolation response<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<p>Use the table to separate thermal carrying questions from switching and fault questions. A manufacturer may document an increase in carrying capability for a particular multipole arrangement without allowing an equivalent increase in making or breaking capability. Read the exact conditions rather than transferring a rule from another product family.<\/p>\n<p>Connecting adjacent poles of one documented device is also different from paralleling independent contactors. One mechanism can constrain some timing relationships, while separate mechanisms introduce additional variability. Neither arrangement should receive a multiplier taken from an unrelated catalog.<\/p>\n<h2>What happens when one branch fails<\/h2>\n<p>If a branch becomes open, the remaining branch may carry the complete load until the system detects and responds. Define whether that event is permitted, for how long and under what current. An arrangement sized only for perfect sharing may lose its thermal margin immediately after this failure.<\/p>\n<p>A welded branch creates a different problem: commanding both coils off may leave the circuit connected. Ordinary auxiliary feedback may not prove the main-current path is open. Review the actual diagnostic coverage and the means available to interrupt the circuit when one branch remains conductive.<\/p>\n<p>A high-resistance branch can be harder to recognize than an open circuit. Current redistributes, leaving another branch more heavily loaded while the degraded joint may still generate localized heat. Monitoring only the total current can miss that condition. Maintenance criteria should account for branch measurements where the design relies on current sharing.<\/p>\n<h2>Plan measurements around the decision<\/h2>\n<p>Measure each branch current at the same time as total current. Confirm probe range, bandwidth, offset and placement so that a measurement error is not mistaken for imbalance. Include the transient around closing and opening if the intended conclusion concerns switching duty.<\/p>\n<p>Voltage-drop measurements require a defined boundary. Measuring across the complete branch answers a different question from measuring only across the contactor studs. Record the exact sensing locations, current, temperature and contact state. A millivolt reading without these details is difficult to compare with another test.<\/p>\n<p>Thermal assessment should include conductors, lugs, terminal interfaces and the contactor body under the representative enclosure conditions. An open-bench test may have cooling that the production assembly does not. Do not declare a device acceptable solely because its exterior looks similar to the adjacent unit.<\/p>\n<h2>Why equal cable length is insufficient<\/h2>\n<p>Equal cable length can reduce one source of imbalance, but it does not equalize contact resistance or joint condition. Cable routing can also change cooling and mechanical loading at terminals. The busbar or cable layout must remain within the manufacturer&#8217;s mechanical and electrical instructions.<\/p>\n<p>Do not add unreviewed resistance merely to force a favorable current ratio. A deliberate balancing element creates extra loss, temperature rise and fault considerations. If such an approach is proposed, the responsible designer must evaluate the entire arrangement rather than treating it as an assembly adjustment.<\/p>\n<p>Likewise, reducing one coil&#8217;s drive to change its timing is not a sound general balancing method. It can affect pickup reliability, release behavior and heat. Use the documented coil interface and obtain approval for the actual combination of control and power hardware.<\/p>\n<figure><img decoding=\"async\" loading=\"lazy\" src=\"https:\/\/sayoon-dc.com\/wp-content\/uploads\/2026\/05\/czw400a_s1-2.webp\" alt=\"SAYOON DC contactor product view\"><\/figure>\n<h2>Validation and acceptance criteria<\/h2>\n<p>Define the worst permitted branch current, terminal temperature and switching event before selecting a test. Establish how the design responds to one branch unavailable, abnormal feedback and a control-power fault. Include relevant current direction and maximum source voltage, not merely the average operating point.<\/p>\n<p>Retain measured traces, thermal conditions, wiring revision and product ordering codes. If the arrangement depends on a supplier&#8217;s parallel rating, attach the precise statement and its conditions. A sales email saying that the devices are identical does not explain how current sharing or interruption was established.<\/p>\n<p>Validate repeatability across the relevant range of assembly and operating conditions. The goal is a supported envelope, not a single example with nearly equal currents. Any claimed margin should cover the uncertainties that remain after measurement and the permitted changes over service life.<\/p>\n<p>When maintenance replaces only one branch, review whether the accepted sharing evidence still applies. A new contactor and a worn contactor may not behave like the original matched assembly. The service instructions should state the required checks and replacement policy.<\/p>\n<h2>Buying a supported solution<\/h2>\n<p>Send the supplier the total current profile, DC voltage, load type and exact parallel topology. State the expected making and breaking events separately from continuous carrying. Include ambient conditions, enclosure, conductor arrangement and the intended response when one branch fails.<\/p>\n<p>Ask for the documented current-sharing limits, installation requirements and any restrictions on switching. If these cannot be supplied, compare an appropriately rated single device or another engineered architecture. Saving space or purchase cost is not useful if the finished assembly lacks a defensible rating.<\/p>\n<p>The product illustrations here show disconnected construction references. They do not depict an approved parallel connection. Use current drawings and application evidence for the exact ordering codes before specifying hardware or changing an operating machine.<\/p>\n<h2>Educational background: coil and main contact paths<\/h2>\n<p>The Electrician U introduction explains the distinction between the operating coil and main contacts. Use it as background for identifying the switching device; it does not teach or approve the specific circuit reviewed above.<\/p>\n<div style=\"aspect-ratio:16\/9;position:relative\"><iframe src=\"https:\/\/www.youtube-nocookie.com\/embed\/F2yL2Cs2nHc\" title=\"What is a Contactor and How Does it Work? \u2014 Electrician U\" loading=\"lazy\" allowfullscreen style=\"border:0;width:100%;height:100%\"><\/iframe><\/div>\n<p><a rel=\"noopener nofollow\" href=\"https:\/\/www.youtube.com\/watch?v=F2yL2Cs2nHc\" target=\"_blank\">Watch the Electrician U introduction.<\/a><\/p>\n<h2>Frequently asked questions<\/h2>\n<h3>Can two 100 A contactors simply carry 200 A?<\/h3>\n<p>The arithmetic alone is insufficient. Sharing, installation temperature and a failed branch must be considered, and the exact combination needs documented support. Making and breaking ratings require separate review.<\/p>\n<h3>Will the branches each interrupt half the current?<\/h3>\n<p>Not necessarily. The last closed device can receive the continuing load current and may perform the final interruption. Evaluate the actual timing and complete duty rather than assuming equal division.<\/p>\n<h3>Do equal-length cables guarantee equal current?<\/h3>\n<p>No. Contact resistance, joints, terminal geometry and temperature also influence current. Measure the installed branches and use the manufacturer&#8217;s instructions for the approved arrangement.<\/p>\n<h3>Is this the same as parallel battery strings?<\/h3>\n<p>No. Separate battery strings introduce source-voltage differences and individual protection requirements. This guide concerns parallel switching paths between the same nodes, without separate sources in each branch.<\/p>\n<h2>Product documentation and related guides<\/h2>\n<p>Send the actual schematic and duty to request current drawings and application evidence for the <a href=\"https:\/\/sayoon-dc.com\/product\/czw400a-normally-open-dc-contactor\/\">CZW400A Normally Open DC Contactor construction reference<\/a>. Start with the <a href=\"https:\/\/sayoon-dc.com\/blog\/dc-contactor-selection-guide-key-factors-for-reliable-motor-control\/\">DC contactor selection guide<\/a> for the overall specification. Complementary reading: <a href=\"https:\/\/sayoon-dc.com\/blog\/parallel-bess-battery-string-contactors\/\">How Battery String Contactors Work in Parallel BESS Racks<\/a>, <a href=\"https:\/\/sayoon-dc.com\/blog\/contactor-contact-resistance\/\">Contactor Contact Resistance: What to Measure and How to Interpret It<\/a>, <a href=\"https:\/\/sayoon-dc.com\/blog\/contactor-making-capacity-vs-continuous-current\/\">DC Contactor Making Capacity vs Continuous Current Rating<\/a>.<\/p>\n<h2>Sources and measurement scope<\/h2>\n<p>Keep instrument identification, uncertainty and calibration evidence with the test record; NIST describes the basis of metrological traceability. The sources below explain the stated physical principles or measurement practice. They do not certify the illustrated contactor or prescribe a complete machine safety design.<\/p>\n<ul>\n<li><a rel=\"noopener nofollow\" href=\"https:\/\/openstax.org\/books\/university-physics-volume-2\/pages\/10-2-resistors-in-series-and-parallel\" target=\"_blank\">OpenStax series and parallel circuit relationships<\/a><\/li>\n<li><a rel=\"noopener nofollow\" href=\"https:\/\/www.nist.gov\/metrology\/metrological-traceability\" target=\"_blank\">NIST metrological traceability<\/a><\/li>\n<\/ul>\n<p><script type=\"application\/ld+json\">{\"@context\": \"https:\/\/schema.org\", \"@type\": \"FAQPage\", \"mainEntity\": [{\"@type\": \"Question\", \"name\": \"Can two 100 A contactors simply carry 200 A?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"The arithmetic alone is insufficient. Sharing, installation temperature and a failed branch must be considered, and the exact combination needs documented support. Making and breaking ratings require separate review.\"}}, {\"@type\": \"Question\", \"name\": \"Will the branches each interrupt half the current?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"Not necessarily. The last closed device can receive the continuing load current and may perform the final interruption. Evaluate the actual timing and complete duty rather than assuming equal division.\"}}, {\"@type\": \"Question\", \"name\": \"Do equal-length cables guarantee equal current?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"No. Contact resistance, joints, terminal geometry and temperature also influence current. Measure the installed branches and use the manufacturer's instructions for the approved arrangement.\"}}, {\"@type\": \"Question\", \"name\": \"Is this the same as parallel battery strings?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"No. Separate battery strings introduce source-voltage differences and individual protection requirements. This guide concerns parallel switching paths between the same nodes, without separate sources in each branch.\"}}]}<\/script><\/p>\n<style>.sy-table-wrap{max-width:100%;overflow-x:auto}.sy-table-wrap table{min-width:650px;width:100%;border-collapse:collapse}.sy-table-wrap th,.sy-table-wrap td{padding:12px;border:1px solid #d5dce4;vertical-align:top;text-align:left}figure{margin:24px 0}figure img{max-width:100%;height:auto}<\/style>\n","protected":false},"excerpt":{"rendered":"<p>\u041f\u0435\u0440\u0435\u0434 \u0434\u043e\u0431\u0430\u0432\u043b\u0435\u043d\u0438\u0435\u043c \u043d\u043e\u043c\u0438\u043d\u0430\u043b\u044c\u043d\u044b\u0445 \u0442\u043e\u043a\u043e\u0432 \u043e\u0446\u0435\u043d\u0438\u0432\u0430\u0439\u0442\u0435 \u043f\u0430\u0440\u0430\u043b\u043b\u0435\u043b\u044c\u043d\u044b\u0435 \u043a\u043e\u043d\u0442\u0430\u043a\u0442\u043e\u0440\u044b \u043f\u043e \u0441\u043e\u043f\u0440\u043e\u0442\u0438\u0432\u043b\u0435\u043d\u0438\u044e \u043e\u0442\u0441\u0435\u043a\u043e\u0432, \u0440\u0430\u0431\u043e\u0447\u0438\u043c \u0442\u043e\u043a\u0430\u043c \u00ab\u043f\u0435\u0440\u0432\u044b\u0439 \u0437\u0430\u043c\u044b\u043a\u0430\u043d\u0438\u0435 \u2014 \u043f\u0435\u0440\u0432\u044b\u0439 \u0440\u0430\u0437\u0440\u044b\u0432\u00bb \u0438 \u00ab\u043f\u043e\u0441\u043b\u0435\u0434\u043d\u0438\u0439 \u0440\u0430\u0437\u0440\u044b\u0432\u00bb, \u0430 \u0442\u0430\u043a\u0436\u0435 \u043f\u043e \u043f\u043e\u043a\u0430\u0437\u0430\u0442\u0435\u043b\u044f\u043c \u0442\u0435\u0440\u043c\u043e\u0441\u0442\u043e\u0439\u043a\u043e\u0441\u0442\u0438 \u0438 \u043e\u0434\u0438\u043d\u043e\u0447\u043d\u044b\u043c \u0437\u0430\u043c\u044b\u043a\u0430\u043d\u0438\u044f\u043c.<\/p>","protected":false},"author":4,"featured_media":4392,"comment_status":"open","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_gspb_post_css":"","footnotes":""},"categories":[1],"tags":[61],"class_list":["post-3829","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-blog","tag-dc-contactor-engineering"],"blocksy_meta":{"styles_descriptor":{"styles":{"desktop":"","tablet":"","mobile":""},"google_fonts":[],"version":7}},"_links":{"self":[{"href":"https:\/\/sayoon-dc.com\/ru\/wp-json\/wp\/v2\/posts\/3829","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/sayoon-dc.com\/ru\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/sayoon-dc.com\/ru\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/sayoon-dc.com\/ru\/wp-json\/wp\/v2\/users\/4"}],"replies":[{"embeddable":true,"href":"https:\/\/sayoon-dc.com\/ru\/wp-json\/wp\/v2\/comments?post=3829"}],"version-history":[{"count":4,"href":"https:\/\/sayoon-dc.com\/ru\/wp-json\/wp\/v2\/posts\/3829\/revisions"}],"predecessor-version":[{"id":5109,"href":"https:\/\/sayoon-dc.com\/ru\/wp-json\/wp\/v2\/posts\/3829\/revisions\/5109"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/sayoon-dc.com\/ru\/wp-json\/wp\/v2\/media\/4392"}],"wp:attachment":[{"href":"https:\/\/sayoon-dc.com\/ru\/wp-json\/wp\/v2\/media?parent=3829"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/sayoon-dc.com\/ru\/wp-json\/wp\/v2\/categories?post=3829"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/sayoon-dc.com\/ru\/wp-json\/wp\/v2\/tags?post=3829"}],"curies":[{"name":"\u0432\u043f","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}